Jag också Har två boxar, men ingen av dom fungerar.
För mig står det enbart "Please check your internet connection and portal URL.....
Internet har jag både via Ethernet samt Wifi så det är inte problemet.
Snälla hjälp ... Jag vet inte vad som händer .. alltid det här problemet
Infomir blockar IPTV??
Moderator: otto
Re: Infomir blockar IPTV??
Har inget med Infomir block i det här fallet isf skulle du fått fram Copyright meddelandet där.
TVHeadend, Kodi, Dreambox/Enigma2 , RaspberryPi 3/LibreELEC
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Re: Infomir blockar IPTV??
The MAG devices are losing the portal settings after updating the device to the latest version of system software and this will not allow the users to add any portal addresses to the device.
So the event of any blockage by infomir, you can use the below methods to unblock your MAG devices.
In this guide, we will teach you how to downgrade the system software to a version that works with IPTV portals or install an image file that brings back the portal settings and IPTV channels via a USB drive if your device is blocked by infomir and you are no longer able to receive any IPTV channels.
Important notice: You must TURN OFF the AUTO UPDATE feature for your MAG device. We can't stress this enough. Auto update feature must be turned off from the settings, otherwise, it will cause problems.
Blocked devices by infomir (MAG 250-254-256-322-324)
If your device is blocked by infomir, you can use the below noblock image files to restore your access to IPTV channels again.
Start by downloading the image file based on your device model via the links below and copy it inside a USB flash drive. Important note: Make sure that the USB flash drive has a decent quality and the storage capacity is less than 16 GB.
MAG250: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
MAG254: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
MAG256: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
MAG322: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
MAG324: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
The USB drive must include the below requirements:
It must be FAT32 file system format.
If there is more than one partition on the USB drive, you should use the first one.
*Please note that you must TURN OFF the AUTO UPDATE feature for your MAG device*
How to install the noblock image file
For MAG250-254:
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it mag250 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
Connect prepared USB-drive to STB socket.
Open System settings ⇒ Software update.
In the window Software update set Update method = USB. You can see two new options:
Disk - name of USB-drive
Path - Path to update file on the USB-drive
Select Verify (OK) to make sure that the STB detects imageupdate file.
If the file has been detected and can be read you'll see Software Update window.
In Software Update window you can see descriptions of the software versions: the Current version (operating in STB) and New version (available on the USB drive).
To begin to update click Update (F1) in the Software Update window.
Wait until the update is complete. Status of the software update is displayed by progress bar and comments.
After software loads, STB will automatically reboot.
For MAG256:
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it mag256 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
Insert the prepared USB drive in STB slot.
Open System settings ⇒ Software update.
In the Software update window set Update method = USB. You can see two new options:
Disk - name of USB-drive;
Path - Path to update file on the USB-drive.
Select Verify (OK) to make sure that the STB has detected the imageupdate file.
If the file is detected and readable successfully you'll see Software Update window.
In the Software Update window are descriptions of the software versions: the Current version (operating in STB) and New version (available on the USB drive).
To begin the update click Update (F1) in the Software Update window.
Wait until the update process is complete. The status of the software update is displayed by progress bar and comments.
When the software is updated the STB will automatically reboot.
For MAG322-324:
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it mag322 or mag324 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
1. Connect prepared USB-drive to STB. You can use any USB connector of STB: both rear or front.
2. Open Settings⇒ System settings ⇒ Software update.
3. In Software update window set Update method = USB. You can see two new options:
Disk - name of USB-drive
Path - Path to update file on the USB-drive
4. Select Verify (OK) to make sure that STB can detect imageupdate file.
5. If the file is detected and readable successfully you'll see Software Update window.
10. Select subsequent operation after comparing Current and New versions:
To start update push Update (F1).
11. Wait until the update process is complete. After completing the update, the STB automatically reboots.
Note. Do not turn off STB and plug off USB drive until the end of the update.
There you have it. The above examples are for the devices that no longer have access to IPTV channels and you can use the mentioned ways to restore access to IPTV channels. If your device was not listed in the article up to now, you can skip the no block update and simply downgrade your device to the factory image and still bypass the blockage by infomir. In the above tutorial, we will show you how to do it.
Here is the list of image files for the downgrade:
MAG250: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG254: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG256: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG322: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG324: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG349: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG351: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG250-254
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it based on the DEVICE MODEL which can be mag250 or mag250 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
Connect prepared USB-drive to STB socket.
Open System settings ⇒ Software update.
In the window Software update set Update method = USB. You can see two new options:
Disk - name of USB-drive
Path - Path to update file on the USB-drive
Select Verify (OK) to make sure that the STB detects imageupdate file.
If the file has been detected and can be read you'll see Software Update window.
In Software Update window you can see descriptions of the software versions: the Current version (operating in STB) and New version (available on the USB drive).
To begin to update click Update (F1) in the Software Update window.
Wait until the update is complete. Status of the software update is displayed by progress bar and comments.
After software loads, STB will automatically reboot.
MAG256
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it mag256 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
Insert the prepared USB drive in STB slot.
Open System settings ⇒ Software update.
In the Software update window set Update method = USB. You can see two new options:
Disk - name of USB-drive;
Path - Path to update file on the USB-drive.
Select Verify (OK) to make sure that the STB has detected the imageupdate file.
If the file is detected and readable successfully you'll see Software Update window.
In the Software Update window are descriptions of the software versions: the Current version (operating in STB) and New version (available on the USB drive).
To begin the update click Update (F1) in the Software Update window.
Wait until the update process is complete. The status of the software update is displayed by progress bar and comments.
When the software is updated the STB will automatically reboot.
MAG322-324-349-351
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it based on your DEVICE MODEL such as mag322 or mag324 etc and then copy the "imagefile" inside that folder.
Step 1: Bringing up the System Recovery Utility menu
To do this:
Power off (unplug the power supply) the STB.
Push and hold the Menu button on the remote control (it should be directed straight to the STB).
Still holding the Menu button power the STB on (plug in the power supply).
Wait for (~10 seconds) System Recovery Utility menu.
Release the Menu button.
Step 2: Go through the below path :
Select Upgrade tools ⇒ Upgrade Software ⇒ Using USB ⇒ Yes.
The info about software update status is displayed at the bottom of the screen.
Wait until the update process is complete. After completing the update, STB automatically reboots.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
Thanks!
So the event of any blockage by infomir, you can use the below methods to unblock your MAG devices.
In this guide, we will teach you how to downgrade the system software to a version that works with IPTV portals or install an image file that brings back the portal settings and IPTV channels via a USB drive if your device is blocked by infomir and you are no longer able to receive any IPTV channels.
Important notice: You must TURN OFF the AUTO UPDATE feature for your MAG device. We can't stress this enough. Auto update feature must be turned off from the settings, otherwise, it will cause problems.
Blocked devices by infomir (MAG 250-254-256-322-324)
If your device is blocked by infomir, you can use the below noblock image files to restore your access to IPTV channels again.
Start by downloading the image file based on your device model via the links below and copy it inside a USB flash drive. Important note: Make sure that the USB flash drive has a decent quality and the storage capacity is less than 16 GB.
MAG250: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
MAG254: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
MAG256: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
MAG322: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
MAG324: https://cdn-static.ams3.cdn.digitalocea ... oblock.zip
The USB drive must include the below requirements:
It must be FAT32 file system format.
If there is more than one partition on the USB drive, you should use the first one.
*Please note that you must TURN OFF the AUTO UPDATE feature for your MAG device*
How to install the noblock image file
For MAG250-254:
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it mag250 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
Connect prepared USB-drive to STB socket.
Open System settings ⇒ Software update.
In the window Software update set Update method = USB. You can see two new options:
Disk - name of USB-drive
Path - Path to update file on the USB-drive
Select Verify (OK) to make sure that the STB detects imageupdate file.
If the file has been detected and can be read you'll see Software Update window.
In Software Update window you can see descriptions of the software versions: the Current version (operating in STB) and New version (available on the USB drive).
To begin to update click Update (F1) in the Software Update window.
Wait until the update is complete. Status of the software update is displayed by progress bar and comments.
After software loads, STB will automatically reboot.
For MAG256:
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it mag256 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
Insert the prepared USB drive in STB slot.
Open System settings ⇒ Software update.
In the Software update window set Update method = USB. You can see two new options:
Disk - name of USB-drive;
Path - Path to update file on the USB-drive.
Select Verify (OK) to make sure that the STB has detected the imageupdate file.
If the file is detected and readable successfully you'll see Software Update window.
In the Software Update window are descriptions of the software versions: the Current version (operating in STB) and New version (available on the USB drive).
To begin the update click Update (F1) in the Software Update window.
Wait until the update process is complete. The status of the software update is displayed by progress bar and comments.
When the software is updated the STB will automatically reboot.
For MAG322-324:
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it mag322 or mag324 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
1. Connect prepared USB-drive to STB. You can use any USB connector of STB: both rear or front.
2. Open Settings⇒ System settings ⇒ Software update.
3. In Software update window set Update method = USB. You can see two new options:
Disk - name of USB-drive
Path - Path to update file on the USB-drive
4. Select Verify (OK) to make sure that STB can detect imageupdate file.
5. If the file is detected and readable successfully you'll see Software Update window.
10. Select subsequent operation after comparing Current and New versions:
To start update push Update (F1).
11. Wait until the update process is complete. After completing the update, the STB automatically reboots.
Note. Do not turn off STB and plug off USB drive until the end of the update.
There you have it. The above examples are for the devices that no longer have access to IPTV channels and you can use the mentioned ways to restore access to IPTV channels. If your device was not listed in the article up to now, you can skip the no block update and simply downgrade your device to the factory image and still bypass the blockage by infomir. In the above tutorial, we will show you how to do it.
Here is the list of image files for the downgrade:
MAG250: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG254: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG256: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG322: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG324: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG349: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG351: https://cdn-static.ams3.cdn.digitalocea ... ngrade.zip
MAG250-254
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it based on the DEVICE MODEL which can be mag250 or mag250 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
Connect prepared USB-drive to STB socket.
Open System settings ⇒ Software update.
In the window Software update set Update method = USB. You can see two new options:
Disk - name of USB-drive
Path - Path to update file on the USB-drive
Select Verify (OK) to make sure that the STB detects imageupdate file.
If the file has been detected and can be read you'll see Software Update window.
In Software Update window you can see descriptions of the software versions: the Current version (operating in STB) and New version (available on the USB drive).
To begin to update click Update (F1) in the Software Update window.
Wait until the update is complete. Status of the software update is displayed by progress bar and comments.
After software loads, STB will automatically reboot.
MAG256
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it mag256 and then copy the "imagefile" inside that folder.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
On MAG
Insert the prepared USB drive in STB slot.
Open System settings ⇒ Software update.
In the Software update window set Update method = USB. You can see two new options:
Disk - name of USB-drive;
Path - Path to update file on the USB-drive.
Select Verify (OK) to make sure that the STB has detected the imageupdate file.
If the file is detected and readable successfully you'll see Software Update window.
In the Software Update window are descriptions of the software versions: the Current version (operating in STB) and New version (available on the USB drive).
To begin the update click Update (F1) in the Software Update window.
Wait until the update process is complete. The status of the software update is displayed by progress bar and comments.
When the software is updated the STB will automatically reboot.
MAG322-324-349-351
On PC (preparation for the USB-drive)
Download imageupdate file from the above links.
Put imageupdate file in the USB-drive directory mag<model>. For example, you must create a folder inside the root of your USB flash drive and name it based on your DEVICE MODEL such as mag322 or mag324 etc and then copy the "imagefile" inside that folder.
Step 1: Bringing up the System Recovery Utility menu
To do this:
Power off (unplug the power supply) the STB.
Push and hold the Menu button on the remote control (it should be directed straight to the STB).
Still holding the Menu button power the STB on (plug in the power supply).
Wait for (~10 seconds) System Recovery Utility menu.
Release the Menu button.
Step 2: Go through the below path :
Select Upgrade tools ⇒ Upgrade Software ⇒ Using USB ⇒ Yes.
The info about software update status is displayed at the bottom of the screen.
Wait until the update process is complete. After completing the update, STB automatically reboots.
Note: Do not turn off STB and plug off USB drive until the end of the update.
Do not use the upper letter case for naming the folders or image files.
Thanks!
TVHeadend, Kodi, Dreambox/Enigma2 , RaspberryPi 3/LibreELEC
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Re: Infomir blockar IPTV??
Grymt! Mina föräldrars mag256 slutade fungera i förrgår. Så få ta och testa denna guide och se om man kan få det att funka igen ![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
Re: Infomir blockar IPTV??
Har provat uppdateringen men får ett felmeddelande när jag ska uppdatera
Update status : wrong signature
Någon som vet felet ?
Update status : wrong signature
Någon som vet felet ?
Re: Infomir blockar IPTV??
Hittade detta för att lösa det problemet
I had a clients mag250 after sever flash tries via portal and Bios with 'wrong Signature' result here is a way that resolves the problem.
Needed:
1. networkcable
2. Tool Mcast v2.0
3. Tool DualServer
Procedure:
1. unplug your box
By repluging the power press several times the left down key on the remote to enter the Boot menu (BIOS)
2. go to upgrade tools
3. on your computer make a directory where you put the file Bootstrap and imageupdate in and i suggest put mcast.exe in there too.
4. connect your stb with the ethernet cable to your pc
5. press win+R choose your Ethernet adapter by right clicking on it and go to properties (the last entry)
6. choose internet protocol v4 and set ip to manual enter 192.168.1.1 and press ok
7 goto search enter cmd right click run as administrator
8. with cd.. Cd command navigate to your download location or where you placed the dualserver.exe
9. enter dualserver -f
10 run mcast and change adress of 1st stream to 224.50.0.70:9000
11. start both streams
12 on your stb goto mc update and wait youll see a green msg which tells you the image is recived
Thats it no wrong signature
Finns information även här
https://wiki.infomir.eu/eng/set-top-box ... gMulticast
I had a clients mag250 after sever flash tries via portal and Bios with 'wrong Signature' result here is a way that resolves the problem.
Needed:
1. networkcable
2. Tool Mcast v2.0
3. Tool DualServer
Procedure:
1. unplug your box
By repluging the power press several times the left down key on the remote to enter the Boot menu (BIOS)
2. go to upgrade tools
3. on your computer make a directory where you put the file Bootstrap and imageupdate in and i suggest put mcast.exe in there too.
4. connect your stb with the ethernet cable to your pc
5. press win+R choose your Ethernet adapter by right clicking on it and go to properties (the last entry)
6. choose internet protocol v4 and set ip to manual enter 192.168.1.1 and press ok
7 goto search enter cmd right click run as administrator
8. with cd.. Cd command navigate to your download location or where you placed the dualserver.exe
9. enter dualserver -f
10 run mcast and change adress of 1st stream to 224.50.0.70:9000
11. start both streams
12 on your stb goto mc update and wait youll see a green msg which tells you the image is recived
Thats it no wrong signature
Finns information även här
https://wiki.infomir.eu/eng/set-top-box ... gMulticast
TVHeadend, Kodi, Dreambox/Enigma2 , RaspberryPi 3/LibreELEC
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Re: Infomir blockar IPTV??
Annars så kan ni testa att följa detta istället men det borde fungera med samma fil som ni redan laddat ner.
https://www.reddit.com/r/IPTV/comments/ ... _blocking/
https://www.reddit.com/r/IPTV/comments/ ... _blocking/
TVHeadend, Kodi, Dreambox/Enigma2 , RaspberryPi 3/LibreELEC
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Re: Infomir blockar IPTV??
Jag har en MAG322 och efter att jag testade att köra guiden ovan så finns nu inte möjligheten att lägga till Portal under Servers i Settings. Går jag in under "Servers" i "System Settings" så finns bara valen "General" och "More".. Hur löser man detta? Förklara gärna enkelt och utförligt för jag är ganska novis på sånt här..
Re: Infomir blockar IPTV??
På samma sätt som du gjorde första gången.
All flashning måste göras från "Recovery flash utility" menyn och inte under vanliga "Software update" för då får man det där felet många får med signature.
All flashning måste göras från "Recovery flash utility" menyn och inte under vanliga "Software update" för då får man det där felet många får med signature.
TVHeadend, Kodi, Dreambox/Enigma2 , RaspberryPi 3/LibreELEC
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Xiaomi Mi Box/Live Channels + TVirl & TVheadend addon, TVIP410
Re: Infomir blockar IPTV??
Hej.
Har en mag254.
Sedan två dagar sedan får jag upp: Access to the web page you were trying to visit had been blocked in accordance with manufacturer content protection and piracy prevention policy.
Jag har följt anvisningarna och laddat hem ny software från FreddyyK, https://www.reddit.com/r/IPTV/comments/ ... _blocking/
Dock verkar det inte funka för mig. När jag försöker göra en Software update så står det Wrong signature och boxen flashar inte.
Vore jävligt tacksam för hjälp??
/Aeonizer
Har en mag254.
Sedan två dagar sedan får jag upp: Access to the web page you were trying to visit had been blocked in accordance with manufacturer content protection and piracy prevention policy.
Jag har följt anvisningarna och laddat hem ny software från FreddyyK, https://www.reddit.com/r/IPTV/comments/ ... _blocking/
Dock verkar det inte funka för mig. När jag försöker göra en Software update så står det Wrong signature och boxen flashar inte.
Vore jävligt tacksam för hjälp??
/Aeonizer